Jet Drill Press - Revision history

Djscholl: Updated with additional information

2013-04-27T13:58:30Z

Updated with additional information

Darvon: I asked a question on the FAQ

2013-04-26T00:00:43Z

I asked a question on the FAQ

Djscholl: Added note about table alignment.

2013-02-22T13:11:25Z

Added note about table alignment.

Gsmith at 21:57, 29 January 2013

2013-01-29T21:57:20Z

Djscholl: Initial contents of new page

2013-01-19T01:59:03Z

Initial contents of new page

New page

{{Equipment

| Name = Jet Drill Press

| Intro = It is most often used for drilling holes in wood, plastic, and related materials. With specialized bits, it can also be used for sanding.

| Owner = Dave Scholl

| StorageLocation = In the wood shop on a rolling cart.

| MakeModel = Jet JDP-15M

| PartNumber = Stock No. 354165, Serial No. 7090087

| Documentation =
* [http://content.jettools.com/assets/manuals/354165_man_EN.pdf User manual]
* Please read the drill press safety tips in the [[Drill Press Clamp Safety|Rapidly-Rotating Scythe FAQ]].

| LooksLike = [[File:Jetdrillpress.jpg|Jet drill press photo]]

| Rules =

* Please wear safety glasses!
* Please clamp your work to the drill press table.

| Instructions =

* The chuck key is on a retractable chain on the right-hand side, next to the motor.
* Drill press clamps and the drill press vise are kept in the cart under the drill press.

| OtherReferences = TBD

| MaintenanceInfo = TBD

| ToDos = TBD

| FAQs = TBD

}}
[[Category:Wood Shop]]

← Older revision		Revision as of 21:57, 29 January 2013
Line 35:		Line 35:


−	\| ToDos = ~~TBD~~	+	\| ToDos =

		+	* Build Cabinet for Drill Press tools and accessories

	\| FAQs = TBD		\| FAQs = TBD

@@ Line 23: / Line 23: @@
 * Please wear safety glasses!
 * Please clamp your work to the drill press table.
-* Before you drill, check to make sure your bit is located over the hole in the table. When the table is raised or lowered, it can swing a little bit to the side. If the hole is not aligned under the bit, when the drill goes through the workpiece it will make another divot like the one you can see on the table now.
+* Before you drill, check to make sure your bit is located over the hole in the table. When the table is raised or lowered, it can swing a little bit to the side. If the hole is not aligned under the bit, when the drill goes through the workpiece it will make another divot like the one you can see on the table now. When the table is aligned, lock it down tight with the clamp handle.
 | Instructions =
@@ Line 30: / Line 32: @@
 * Drill press clamps and the drill press vise are kept in the cart under the drill press.
-| OtherReferences = TBD
+| OtherReferences =
-−
 | MaintenanceInfo = TBD
 | ToDos =
@@ Line 42: / Line 42: @@
 | FAQs =
-) Where are drill bits stored?  Is there different bits for wood and metal?  If so, how can I tell them apart?
+# Where are drill bits stored?  A: Some drill bits are stored in the tool crib in plastic bins. Others are stored in the metal shop.
 }}
 [[Category:Wood Shop]]

@@ Line 40: / Line 40: @@
 * Build Cabinet for Drill Press tools and accessories
-| FAQs = TBD
+| FAQs =
 }}
 [[Category:Wood Shop]]