ToDo
(Difference between revisions)
| (8 intermediate revisions by 5 users not shown) | |||
| Line 43: | Line 43: | ||
|mount dust collector switches | |mount dust collector switches | ||
| Second switch needs ran next to the chopsaw! | | Second switch needs ran next to the chopsaw! | ||
| − | | | + | | Greg installed magnet on Saw switch may be ok |
| − | | | + | | G donated Magnet |
|- | |- | ||
|sweep and vaccum | |sweep and vaccum | ||
| Line 52: | Line 52: | ||
|- | |- | ||
|get audio system up and running | |get audio system up and running | ||
| − | |run wire from speakers back to backboard | + | |run wire from speakers back to backboard <- Whats this mean, who do I ask? |
| | | | ||
|terminal strips already in e-room bin | |terminal strips already in e-room bin | ||
| Line 108: | Line 108: | ||
|cyclone fence around kilm | |cyclone fence around kilm | ||
| | | | ||
| − | | | + | |Terry W |
| | | | ||
|- | |- | ||
| Line 162: | Line 162: | ||
|- | |- | ||
|build 3 lockable money boxes | |build 3 lockable money boxes | ||
| − | | | + | | one done 2 to go |
| − | | | + | | Greg Smith |
| − | | | + | | 12.82 |
|- | |- | ||
|build tool holder for vinyl area | |build tool holder for vinyl area | ||
| Line 216: | Line 216: | ||
| | | | ||
|- | |- | ||
| − | + | |hang shop light over table saw | |
| + | |buy shop light for two 4ft T8 bulbs | ||
| + | | | ||
| + | |$20 | ||
| + | |- | ||
| + | |mount pegboard box on NW user storage end cap | ||
| + | |box is clamped in place, needs permanent fastening | ||
| + | | | ||
| + | |$0, supplies on hand | ||
| + | |- | ||
| + | |Build wood shop machine cart | ||
| + | | | ||
| + | | | ||
| + | | | ||
| + | |- | ||
| + | |Install Casters on Wood Shop router table | ||
| + | |Admire how nice it is | ||
| + | |Greg Smith | ||
| + | | | ||
| + | |- | ||
| + | |Move Drill Press to Wood Shop | ||
| + | | | ||
| + | | | ||
| + | | | ||
| + | |- | ||
| + | |Make "I don't know where this goes" boxes for each main area | ||
| + | | | ||
| + | | | ||
| + | | | ||
| + | |- | ||
| + | |Add dust cover to south side of freestanding member storage | ||
| + | | | ||
| + | | | ||
| + | | | ||
| + | |- | ||
| + | |Move SandBlast Station and supplies to East Wall between Welding Zone and Overhead Door | ||
| + | | | ||
| + | |Jim Kemp | ||
| + | |$0 | ||
| + | |- | ||
[[Category:Organization Information]][[Category:Reference Data]] | [[Category:Organization Information]][[Category:Reference Data]] | ||
Revision as of 18:13, 20 November 2012
Welcome to the Potlock to do list, please pick a task and put your name in the column. (any questions? contact Dustin White dustinbikes@gmail.com)
Need supplies? Toss 'em on the ShoppingList and maybe somebody will check that page from their phone next time they're at the store.
| Task | Next Action | Volunteer? | Approx Cost of materials |
|---|---|---|---|
| Clean and sweep under graveyard area | |||
| Rearrange phone buttons so they're accurately labeled | This is a firmware change, I just need to figure out which one it is. | Nate W | $0 |
| Make "how to transfer calls, etc" cheatsheet for each phone | Figure that out! | $0 | |
| make vinyl "propaganda signs" | sayings about keeping the place clean and such | ||
| make stencil on lasercutter | sayings "SWEEP If you can't read this" spraypaint on woodshop floor | ||
| install seals around garage door | |||
| mount dust collector switches | Second switch needs ran next to the chopsaw! | Greg installed magnet on Saw switch may be ok | G donated Magnet |
| sweep and vaccum | |||
| get audio system up and running | run wire from speakers back to backboard <- Whats this mean, who do I ask? | terminal strips already in e-room bin | |
| mount and wire security cameras | |||
| install automatic drain on air compressor | |||
| organize above window lumber storage areas | |||
| organize scrap lumber under chop saw | |||
| Chain link fence cage for dust collector | |||
| add Cowl to furnaces | aim into metal shop, aim at west side of shop. | ||
| Forklift repair | Repair ignition switch | ||
| Replace twitterbot camera | |||
| purge graveyard | |||
| manage scrap metal near welding | |||
| cyclone fence around kilm | Terry W | ||
| assemble last set of orange shelves | the ends arnt the same, either welding together or drilling and bolting | Nate W | |
| find home for injection molders | ?? - current home u no like? | ||
| find new home for paint | |||
| cleanup and revamp hardware land | |||
| fix sandblasters | |||
| build shelf on sw metal shop wall for storage of materials | |||
| rubber shroud for dust collector | |||
| have nick take home lights, juki, and jointer | |||
| go through wood stock and dispose of unusable | |||
| build a workbench area for laser cutter | |||
| build 3 lockable money boxes | one done 2 to go | Greg Smith | 12.82 |
| build tool holder for vinyl area | |||
| find a solution to have am aux jack at commons table for audio | |||
| organize cleaning cabinet | |||
| setup scanner/copier/blog station | |||
| return little busted ass laser to AHA | |||
| build cart for large power supplies | |||
| clean the hell out of craft room | |||
| move rack into kitchen for extra pop | |||
| clean kitchen and mop floor | |||
| buy 3 drawer thingy for kitchen | buy untensils and bowls for kitchen from dollar tree | ||
| hang shop light over table saw | buy shop light for two 4ft T8 bulbs | $20 | |
| mount pegboard box on NW user storage end cap | box is clamped in place, needs permanent fastening | $0, supplies on hand | |
| Build wood shop machine cart | |||
| Install Casters on Wood Shop router table | Admire how nice it is | Greg Smith | |
| Move Drill Press to Wood Shop | |||
| Make "I don't know where this goes" boxes for each main area | |||
| Add dust cover to south side of freestanding member storage | |||
| Move SandBlast Station and supplies to East Wall between Welding Zone and Overhead Door | Jim Kemp | $0 |
