ToDo

NEW TASKS, as of October 2011

Task	Next Action	Volunteer?
Clear Genie-width path to member storage
Construct and affix dry-erase marker holders to every whiteboard
Mount monitor on/near rack, for admin KVM usage
Consolidate adhesives/solvents/cleaners/etc and label each location with pointers to the other locations
Bring blue bins down from attic and wash them all		Matt O
Fridge cleanout		Matt O
Affix QR codes to every tool with a wiki page
Cover roof openings, consider snow-melt drainage in your design
Level concrete near rack
Garage-door concrete
Winterization stuff (Bill putt suggested -- need more specifics)
North & East Storm windows	Get measurements and figure hardware	Steve H
replace flex exaust from laser cuter with solid pipe in steel, will improve air flow about 200%.
we need a stock rack/box in machine shop, 5"x5" by 12"deep eggcrate, about 12 holes, 1/4 ply, could be laser cut, ply frame. - Ask steve H
consolidate and shut down small black freezer
Run air hose to bike shop	run black air hose to new bike shop area
clean up and organize member storage
add dividers to member storage shelves	use tape or paint to divide the shelves into quarters
clean up FIRST area	throw away junk and put all gear into bins below benches
sweep and vacuum your butt off		everyone!
identify emergency exit routes and paint the lines	we have floor marking paint, just need skinny rollers
install other welding curtain	talk to Nate B. he has vision for this
Fix bottom seal on garage door	use quickrete to level ground
install safety chain on theatre lights	get chain for said task
make bins/shelf for welding area metal storage
make a set of cubbies for storage of cut offs in metal shop area	shelves should be 12-14 in deep
finish up audio system	get zoned audio system up and running
hook up outdoor light outside main door
mount and wire security cameras	talk to Joe Bender about camera mount locations
rebuild donation sucker	clean out shop-vac and set up	Nate B
Make boxes to store assorted tools in tool area	use box maker program to laser cut custom boxes

---

OLD LISTS use for inspiration but move relevant tasks to new list above, please only copy the name, and reconsider the "next action" and secure a new volunteer.

---

Can be tackled immediately:

Task	Next Action	Volunteer?
Change thermostat batteries	Determine what they take
Rewire laser exhaust on 230v	Doublecheck SSR and PSU	Joe
E-room pretty lights, wire to second switch.	Install outlet, extend cord.	Cherish
Clean blue bins
Craft room: Establish Cricut-stuff box	Find and label suitable box
Kitchen: Label cabinets with contents		who?
Kitchen: Fridge cleanout
Launder everything launderable
Welding area: Commission P&H welder	Print a copy of the manual
Bike shop: Air feed	Restring hose, mount manifold/regulator	Nate B
Bike shop	move bike shop to corner near water heater	dustin
Shop: Redundant tools and rearrange	Identify owners of redundant tools	Nick
Tool area: Archive dubiously-useful hardware	Find sturdy boxes for metal thingies
Defrag member storage	Assemble majority of members	Everyone!
Rebuild Donation-Sucker	Clean shop-vac	Nate B
Sweep and vacuum your butt off
Tape off emergency exit pathways	Decide what those are
Photograph everything for insurance documentation	Figure out where to store photos when done
E-room: Network jacks	Test and trace existing wire	Nate W
Security cameras	Mount and wire	Talk to Nate B
Cleaning supplies / flammables / etc	Decide on scheme and implement, then label.
MSDS update	Find binder!
Shop area: Run copper wire in dust collector hose	Talk to Nick
Repair / upgrade selected 115V circuits	Documentation: Breaker Panels	Dave S
Mount and wire additional ceiling fans	get it done before we all melt	Brad
Small project Storage	Move lockers and build additional storage locker units	Brad
E-Room shelving	Clean space, assemble units, place units and fasten to wall	Brad
clean up First area	clear benches, stow supplies in boxes	Dustin/Ted
		...

Just need supplies:

Task	Next action / need	Volunteer
E-room fluorescent lights, fix flicker	Note type of ballasts, and obtain replacement(s)
E-room powerstrips	Obtain another wall-mountable strip with switch
Welding curtains	Need a pile of sticks and string and sketches	Nate B
Cover and insulate roof-fan openings	Needs foam, plastic, sticks, and plan.	Nate B
Tool area: Sort electrical parts	Just need some boxes...	Nate B
Doorbell	Easy Button not weatherproof. Find a button that is.	Nate B
Craft-room bench cushion	?
Craft-room table painting	?
Floor gouge in FIRST area	Quickrete
Garage door bottom seal	Quickrete
Garage door side seals	Identify and obtain appripriate thingies
Safety chain for theater lights	Identify appropriate type of chain or cable
Lubricate Genie column	Boe-Lube solid (MSC carries it)	Nate B
...

Need approval, concept, or otherwise not immediately doable:

Task	Needs	Champion
Welding area: Store scrap metal	Concept	Nate B / Karen?
Whiteboard room lights	Find a useful plug-in PIR outlet / Wattstopper perhaps?	Nate B
Multizone audio	Cohesive plan, mounting location, speaker wire?
Signage	Is this idea still alive?	Ross
Shower leak	Assess problem, identify repairs needed
Security (PIR) sensors	Need something to wire 'em back to	Eric M?
Vending machine light	Concept, wiring diagram...
Update website static pages	Concept, see i3detroit-web group	Nate B
Sign proposal		Dustin
Outdoor light	Concept, box, conduit, permit??
...