ToDo

From i3Detroit
Revision as of 17:15, 29 January 2012 by Nbezanson (Talk | contribs)

Jump to: navigation, search

Bored? Got an urge to do stuff for the space? Pick a task from this list, and advance it. Ask for help if you need it.

Need supplies? Toss 'em on the ShoppingList and maybe somebody will check that page from their phone next time they're at the store.


Task Next Action Volunteer? Approx Cost of materials
Fix OFF switch on Grizzly (wood) band saw.
Replace light fixture just inside the main door Nate W got the fixtures. Now need to be installed Nate W $22
Buy more T-8 bulbs 10+ pack, We use T-8 4100k Could always use more. Nate W $20-25
Move new-ish light over the utilitub to the emergency lighting circuit to illuminate light switches and breaker panels in the dark shop Emergency circuit is apparently in the same conduit as the circuit that powers the light now
Move tool crib drop cord reel from light-switch circuit to another circuit ask Dave S about an (apparently) unused circuit in the SE shop ceiling conduits
Replace ceiling fan by parts area, rehang commons fan, de-kludge fan wiring note: new fan is on kiln table, labeled "FAN" Dave S
Uninstall old ass furnace in large door bay. Unit is inefficient, and useless! Genie + Forklift $0 ?
Move light switches near door Install switches by main entrance to control all overhead lights.
- Leave machine shop separate, reroute switch within machine shop.
 ??
Clean crud out of washtub! EWWWW :( You are my hero!
Vinyl propaganda signs Come up with sayings "Sweep around machines, do I look like your mom?" Nate W/Vinyl Team $0
Redo drip pan above server rack before it turns into a waterfall. Install drain tube down to washtub $10-20?
Install shelving in Power wheels area, re-purpose benches. Find more 12-14' pallet racking nate w / rocco / anyone!  ???
Garage-door floor Raise concrete level below door higher than outside.
Home depot has thick rubber seals that would help too. $10ish
Nate W $4-14
Redo shop restroom Remount & Paint stalls, Title floor, Cover walls. $$$? - a lot
seal off end of member storage shelves in woodshop so that equipment can be butted against it. Screw panels to ends of shelves, and between to create full wall. $48
Mount and wire motor to dust collector Ted and Nate B
are looking into this.
Mount dust collector relays 1 on dust collector, 2nd near table saw.
 
PRIOR TASKS THAT STILL NEED DONE!!
Update MSDS binder by door
Affix laser-cutter inner lights with Dual-Lock strips Get high off 3m adhesive primer Anyone? See Nate B $0
Construct shop-vac accessories rack Gather all nozzles and design rack
Clear Genie-width path to member storage $0
remove MDF table/counters from wood shop ask Nick to take home/remove $0
Mount monitor on/near rack, for admin KVM usage $0
Consolidate adhesives/solvents/cleaners/etc and label
each location with pointers to the other
Cover roof openings, consider snow-melt drainage in your design Adjust rear shop cover, cover is not air tight and has shifted with a draft. $0
Winterization stuff (Bill putt suggested -- need more specifics) $0
add dividers to member storage shelves use tape or paint to divide the shelves into quarters
clean up FIRST area throw away junk and put all gear into bins below benches $0
sweep and vacuum your butt off everyone! $0
identify emergency exit routes and paint the lines we have floor marking paint, (update:picked up skinny rollers) $0
finish up audio system mount amplifiers in rack, mount speakers, run wire $0
mount and wire security cameras talk to Joe B or Nate B about camera mount locations  ?
Make boxes to store assorted tools in tool area identify tools which need boxes $0
remove desk from whiteboard room $0
organize fastener area organize and label fasteners $0
build table for little sanblaster talk to dustin about getting the sandblaster set up $9
Reroute all e-room bench equipment power cords to go behind shelf
(empty shelf, rip half an inch off its depth, remount it, reload it)
$0
Label all E-room gear power cords (Many already done, follow example) $0
Document 115V circuits Documentation: Breaker Panels Dave S
allocate two of the steel drums for aluminum and steel scrap put vinyl signage on drums $0
store unused dust collector manifold and filters in loft put filters in garbage bags $0
move 5sl printer away from print shop over to server area. $0
organize vinyl cutter area.
level rough concrete $8
make signage to identify circuit breakers $0
make a cart for folding chairs  ???
replace vents in office area  ???
cut vent in electronics room and install vent cover there is a vent in wall that has been drywalled over  ???
install cisco network gear into rack rocco will be bringing in a rack for this purpose rocco $0
clean up kitchen and throw out old stock of goods $0
install small shelf to place microwave in cabinet talk to dustin for direction $0
talk to Bob B about painting fridge (brown one) $0
make soda can dispensers for white refrigerator talk to dustin for direction  ???
pull down drum from metal dust collector in metal shop assess if machine is in functioning order
Mount Sorensen PSU under e-lab shelf Nate or Joe