Wood Shop Training
(Difference between revisions)
(Content relocated from individual equpment pages) |
(Improved formatting) |
||
| Line 42: | Line 42: | ||
| − | + | '''Advanced Drill Press Topics''' | |
| − | + | * Adjusting the table height | |
| − | + | * Setting the vertical travel stops | |
| − | + | * Using a drill press vise | |
| − | + | * Dust control system | |
| − | + | * How to tell when a bit needs to be sharpened | |
| − | + | * Changing the drill speed | |
| − | + | * Using Forstner and other large (over 1/2 in) bits | |
| − | + | * Consumables costs | |
| − | + | * Using brushes or sanders in the chuck | |
| − | + | * Making fixtures for repeating hole locations | |
| − | + | * Making fixtures for workpiece clamping | |
| − | + | '''Advanced Disc Sander Topics''' | |
| − | + | * Adjusting the table angle | |
| − | + | * Selecting sandpaper grits | |
| − | + | * Replacing sandpaper disc | |
| − | + | * How to tell when the sandpaper needs to be replaced | |
| − | + | * Consumables costs | |
| − | + | * Review all core topics above | |
| − | + | * Adjusting the table-disc clearance | |
| − | + | * Making special tools and jigs | |
| − | + | '''Advanced Band Saw Topics''' | |
| − | + | * Using the miter gauge | |
| − | + | * Using the fence | |
| − | + | * Dust control system | |
| − | + | * How to tell when the blade needs to be replaced | |
| − | + | * Consumables costs | |
| − | + | * Using fixtures for controlled cutting | |
| − | + | * Adjusting the table tilt angle | |
| − | + | * Selecting a blade | |
| − | + | * Replacing the blade (tension and tracking adjustments) | |
| − | + | * Adjusting Upper and Lower blade guides | |
| − | + | * Setting upper and lower blade guide clearances | |
| − | + | * Resawing | |
| − | + | * Making fixtures for locating/aligning the workpiece | |
| − | + | '''Dovetail Joints''' | |
| + | * TBD | ||
| − | + | '''Mortise and Tenon Joints''' | |
| + | * TBD | ||
| Line 92: | Line 94: | ||
(Small Group or Individual Training) | (Small Group or Individual Training) | ||
| − | |||
| − | * | + | '''Hardwood Candlestick Holder''' |
| + | * TBD | ||
| + | |||
| + | '''Rolling Equipment Cart for Your Home Shop''' | ||
| + | * TBD | ||
[[Category:Wood Shop]] | [[Category:Wood Shop]] | ||
Revision as of 12:30, 11 November 2012
Introductory Wood Shop Class
(Group or Individual Training)
- Wood Shop Tour
- Safety glasses, dangling hair, hoodie strings, etc.
- Cleaning up: shop vac, brush, dustpan, broom, trashcans
- Rockwell Drill Press
- Power switch location/operation
- Workpiece materials compatible with this machine
- Clamping the workpiece safely
- How hard to push the drill bit into the workpiece
- Marking an accurate hole location
- Center punch / center drill to begin holes
- Selecting drill bits
- Changing drill bits
- Delta 12in Disc Sander
- Power switch location/operation
- Workpiece materials compatible with this machine
- Holding the workpiece safely
- Cleaning with cleaning stick
- Dust control
- Grizzly 16in Band Saw, Craftsman 12in Band Saw
- Using the band saw light
- Power switch/EPO location and operation
- Workpiece materials compatible with this machine
- Raising/lowering the upper blade guides
- Holding the workpiece safely
- Using a push stick
- How hard to push the workpiece
- Sawing along a pencil line
- Sawing curves
- Introductory Class Project
- Birdhouse
Advanced/Specialized Wood Shop Classes
(Small Group or Individual Training)
Advanced Drill Press Topics
- Adjusting the table height
- Setting the vertical travel stops
- Using a drill press vise
- Dust control system
- How to tell when a bit needs to be sharpened
- Changing the drill speed
- Using Forstner and other large (over 1/2 in) bits
- Consumables costs
- Using brushes or sanders in the chuck
- Making fixtures for repeating hole locations
- Making fixtures for workpiece clamping
Advanced Disc Sander Topics
- Adjusting the table angle
- Selecting sandpaper grits
- Replacing sandpaper disc
- How to tell when the sandpaper needs to be replaced
- Consumables costs
- Review all core topics above
- Adjusting the table-disc clearance
- Making special tools and jigs
Advanced Band Saw Topics
- Using the miter gauge
- Using the fence
- Dust control system
- How to tell when the blade needs to be replaced
- Consumables costs
- Using fixtures for controlled cutting
- Adjusting the table tilt angle
- Selecting a blade
- Replacing the blade (tension and tracking adjustments)
- Adjusting Upper and Lower blade guides
- Setting upper and lower blade guide clearances
- Resawing
- Making fixtures for locating/aligning the workpiece
Dovetail Joints
- TBD
Mortise and Tenon Joints
- TBD
Wood Shop Class Projects
(Small Group or Individual Training)
Hardwood Candlestick Holder
- TBD
Rolling Equipment Cart for Your Home Shop
- TBD
